Wim System Control lus qhia

Wim System Control Instructions

Lus piav qhia luv luv:


Product Detail

Khoom cim npe

Txheej txheem cej luam

Enviko quartz dynamic hnyav qhov system txais Windows 7 embedded operating system, PC104 + tsheb npav txuas ntxiv mus thiab dav qhov ntsuas kub.Lub kaw lus yog tsim los ntawm cov maub los, them amplifier thiab IO maub los.Lub kaw lus sau cov ntaub ntawv ntawm dynamic hnyav sensor (quartz thiab piezoelectric), hauv av sensor coil (laser ending detector), qag identifier thiab kub sensor, thiab ua rau lawv ua tiav cov ntaub ntawv tsheb thiab hnyav cov ntaub ntawv, nrog rau hom qag, qag naj npawb, wheelbase, log tsheb. naj npawb, qag luj, qag pawg luj, tag nrho qhov hnyav, overrun npaum li cas, ceev, kub, thiab lwm yam. Nws txhawb lub sab nraud lub tsheb hom identifier thiab qag identifier, thiab lub kaw lus cia li sib tw los ua ib tug ua tiav tsheb cov ntaub ntawv upload los yog cia nrog lub tsheb hom kev txheeb xyuas.

Lub kaw lus txhawb ntau hom sensor.Tus naj npawb ntawm cov sensors nyob rau hauv txhua txoj kab tuaj yeem teeb tsa los ntawm 2 mus rau 16. Tus nqi amplifier nyob rau hauv lub kaw lus txhawb nqa imported, domestic thiab hybrid sensors.Lub kaw lus txhawb IO hom lossis hom network los ua kom lub koob yees duab ntes muaj nuj nqi, thiab lub kaw lus txhawb nqa kev ntes cov zis tswj ntawm pem hauv ntej, pem hauv ntej, tus Tsov tus tw thiab tus Tsov tus tw.

Lub kaw lus muaj lub luag haujlwm ntawm lub xeev tshawb pom, lub kaw lus tuaj yeem kuaj xyuas cov xwm txheej ntawm cov cuab yeej tseem ceeb hauv lub sijhawm, thiab tuaj yeem kho thiab xa cov ntaub ntawv thaum muaj xwm txheej txawv txav;lub kaw lus muaj kev ua haujlwm ntawm cov ntaub ntawv tsis siv neeg cache, uas tuaj yeem txuag cov ntaub ntawv ntawm cov tsheb kuaj pom txog li ib nrab xyoo;lub kaw lus muaj kev ua haujlwm ntawm kev saib xyuas tej thaj chaw deb, Txhawb tej thaj chaw deb desktop, Radmin thiab lwm yam kev khiav hauj lwm tej thaj chaw deb, txhawb tej thaj chaw deb fais fab rov pib dua;lub kaw lus siv ntau yam kev tiv thaiv txhais tau tias, suav nrog peb-theem WDT kev txhawb nqa, FBWF kev tiv thaiv kev tiv thaiv, kab mob tua kab mob software, thiab lwm yam.

Technical parameters

zog AC220V 50Hz
ceev ntau yam 0.5 km / h100 km / h
kev faib khoom d = 50 kg
qag kam rau ua ± 10% ceev ceev
tsheb qhov tseeb theem 5 chav, chav kawm 10, chav kawm 2(0.5 km / h20 km / h)
Lub tsheb sib cais raug ≥99%
Lub tsheb paub tus nqi ≥98%
axles load range 0,5t :ua40t ib
Txoj kab khiav 5 kab
Sensor channel 32 channels, lossis rau 64 channels
Sensor layout Txhawb ntau hom sensor layout, txhua txoj kab raws li 2pcs los yog 16pcs sensor xa, txhawb ntau yam ntawm lub siab sensors.
Lub koob yees duab trigger 16channel DO cais cov zis tawm los yog hom kev sib txuas network
Kev tshawb nrhiav xaus 16channel DI kev sib cais tawm tswv yim txuas coil teeb liab, laser xaus nrhiav hom lossis nws pib xaus hom.
System software Embedded WIN7 operating system
Axle ID nkag mus Txhawb ntau lub log qag lees paub (quartz, infrared photoelectric, zoo tib yam) los ua kom tiav cov ntaub ntawv tsheb
Tsheb hom ID nkag mus nws txhawb nqa lub tsheb hom kev txheeb xyuas qhov system thiab ua tiav cov ntaub ntawv tsheb nrog cov ntaub ntawv ntev, dav thiab qhov siab.
Txhawb kev tshawb nrhiav bidirectional Txhawb nqa pem hauv ntej thiab thim rov qab nrhiav kom pom kev bidirectional.
Ntaus interface VGA interface, network interface, USB interface, RS232, thiab lwm yam
Lub xeev nrhiav thiab saib xyuas Kev txheeb xyuas qhov xwm txheej: lub kaw lus pom cov xwm txheej ntawm cov cuab yeej tseem ceeb hauv lub sijhawm, thiab tuaj yeem kho thiab xa cov ntaub ntawv thaum muaj xwm txheej txawv txav.
  Kev saib xyuas tej thaj chaw deb: txhawb tej thaj chaw deb desktop, Radmin thiab lwm yam kev khiav hauj lwm tej thaj chaw deb, txhawb tej thaj chaw deb fais fab rov pib dua.
Cov ntaub ntawv khaws cia Qhov kub thiab txias ntawm lub xeev hard disk, txhawb nqa cov ntaub ntawv khaws cia, txiav, thiab lwm yam.
Kev tiv thaiv Peb theem WDT kev txhawb nqa, FBWF kev tiv thaiv kev tiv thaiv, kev kho kab mob antivirus software.
System hardware ib puag ncig Dav kub kev lag luam tsim
Kub tswj qhov system Cov cuab yeej muaj nws tus kheej tswj qhov kub thiab txias, uas tuaj yeem saib xyuas qhov kub thiab txias ntawm cov cuab yeej hauv lub sijhawm tiag tiag thiab dynamically tswj lub kiv cua pib thiab nres ntawm lub txee.
Siv ib puag ncig (wide temperature design) Kev pabcuam kub: -40 ~ 85 ℃
  Tus txheeb ze humidity: ≤ 85% RH
  Preheating lub sij hawm: ≤ 1 feeb

Ntaus interface

WIM SYSTEM CONTROL INSTRUCTIONS (7)

1.2.1 system khoom sib txuas
Cov khoom siv hauv lub cev feem ntau yog tsim los ntawm kev tswj hwm lub cev, tus nqi amplifier thiab IO input / output controller

product (1)

1.2.2 system controller interface
Lub kaw lus tswj tau tuaj yeem txuas 3 lub suab amplifiers thiab 1 IO maub los, nrog 3 rs232 / rs465, 4 USB thiab 1 network interface.

product (3)

1.2.1 amplifier interface
Tus nqi amplifier txhawb 4, 8, 12 raws (yeem) sensor input, DB15 interface tso zis, thiab qhov ua haujlwm voltage yog DC12V.

product (2)

1.2.1 I / O maub los interface
IO input thiab output controller, nrog 16 cais tawm tswv yim, 16 cais tawm, DB37 tso zis interface, Ua hauj lwm Voltage DC12V.

qhov system layout

2.1 sensor layout
Nws txhawb ntau hom kev teeb tsa sensor xws li 2, 4, 6, 8 thiab 10 ib txoj kab, txhawb txog li 5 txoj kab, 32 sensor inputs (uas tuaj yeem nthuav mus rau 64), thiab txhawb nqa pem hauv ntej thiab thim rov qab ob txoj kev nrhiav kom pom.

WIM SYSTEM CONTROL INSTRUCTIONS (9)
WIM SYSTEM CONTROL INSTRUCTIONS (13)

DI tswj kev sib txuas

16 raws ntawm DI cais tawm tswv yim, txhawb coil maub los, laser ntes thiab lwm yam khoom tiav, txhawb Di hom xws li optocoupler lossis relay input.Cov lus qhia rau pem hauv ntej thiab thim rov qab ntawm txhua txoj kab sib koom ib qho khoom kawg, thiab lub interface tau txhais raws li hauv qab no;

Txoj kab xaus     DI interface chaw nres nkoj naj npawb            ceeb toom
  Tsis muaj 1 txoj kab (rau pem hauv ntej, thim rov qab)    1+,1- Yog hais tias qhov kawg tswj ntaus ntawv yog optocoupler tso zis, qhov kawg ntaus ntawv teeb liab yuav tsum sib haum mus rau lub + thiab - signals ntawm IO maub los ib tug los ntawm ib tug.
   Tsis muaj 2 txoj kab (rau pem hauv ntej, thim rov qab)    2+,2-  
  Tsis muaj 3 txoj kab (rau pem hauv ntej, thim rov qab)    3+,3-  
   Tsis muaj 4 txoj kab (rau pem hauv ntej, thim rov qab)    4+,4-  
  Tsis muaj 5 txoj kab (rau pem hauv ntej, thim rov qab)    5+,5-

DO tswj kev sib txuas

16 channel ua cov tso zis cais tawm, siv los tswj cov kev tswj xyuas lub koob yees duab, kev txhawb nqa theem pib thiab ntog ntug trigger hom.Lub kaw lus nws tus kheej txhawb rau pem hauv ntej hom thiab rov qab hom.Tom qab qhov kev tswj xyuas qhov kawg ntawm hom pem hauv ntej tau teeb tsa, lub hom rov qab tsis tas yuav tsum tau teeb tsa, thiab lub kaw lus hloov pauv tau.Lub interface yog txhais raws li hauv qab no:

Txoj kab xov tooj  Forward trigger Tail trigger Sab taw qhia Tail side direction trigger           Nco tseg
No 1 txoj kab (forward) 1+,1- 6+,6-  11+,11- 12+,12- Lub trigger tswj kawg ntawm lub koob yees duab muaj qhov + - kawg.Lub trigger tswj kawg ntawm lub koob yees duab thiab lub + - teeb liab ntawm IO maub los yuav tsum sib xws ib tug los ntawm ib tug.
No2 txoj kab (rau pem hauv ntej) 2+,2- 7+,7-      
No 3 txoj kab (forward) 3+,3- 8+,8-      
No4 txoj kab (rau pem hauv ntej) 4+,4- 9+,9-      
No 5 kab (rau pem hauv ntej) 5+,5- 10+,10-      
No1 txoj kab (reverse) 6+,6- 1+,1- 12+,12- 11+,11-

phau ntawv qhia kev siv qhov system

3.1 Ua ntej
Kev npaj ua ntej ntsuas ntsuas.
3.1.1 set Radmin
1) Xyuas seb Radmin server puas tau teeb tsa rau ntawm lub ntsuas (lub Hoobkas ntsuas qhov system).Yog tias nws ploj lawm, thov nruab nws
WIM SYSTEM CONTROL INSTRUCTIONS (1)
2) Teem Radmin, ntxiv tus lej thiab tus lej zais
WIM SYSTEM CONTROL INSTRUCTIONS (4)
WIM SYSTEM CONTROL INSTRUCTIONS (48)WIM SYSTEM CONTROL INSTRUCTIONS (47)WIM SYSTEM CONTROL INSTRUCTIONS (8)
3.1.2 system disk tiv thaiv
1) Khiav CMD cov lus qhia kom nkag mus rau DOS ib puag ncig.
WIM SYSTEM CONTROL INSTRUCTIONS (11)
2) Nug EWF tiv thaiv xwm txheej (hom EWFMGR C: nkag mus)
(1) Lub sijhawm no, EWF kev tiv thaiv muaj nuj nqi yog nyob rau (State = ENABLE)
WIM SYSTEM CONTROL INSTRUCTIONS (44)
(Hom EWFMGR c: -communanddisable -live enter), thiab lub xeev yog neeg xiam oob qhab los qhia tias kev tiv thaiv EWF raug kaw
(2) Lub sijhawm no, EWF kev tiv thaiv kev ua haujlwm raug kaw (lub xeev = lov tes taw), tsis tas yuav tsum ua haujlwm tom ntej.
WIM SYSTEM CONTROL INSTRUCTIONS (10)
(3) Tom qab hloov qhov system nqis, teem EWF kom pab
WIM SYSTEM CONTROL INSTRUCTIONS (44)
3.1.3 Tsim nws pib pib shortcut
1) Tsim ib qho shortcut kom khiav.
WIM SYSTEM CONTROL INSTRUCTIONS (12)WIM SYSTEM CONTROL INSTRUCTIONS (18)
WIM SYSTEM CONTROL INSTRUCTIONS (15)
WIM SYSTEM CONTROL INSTRUCTIONS (16)
WIM SYSTEM CONTROL INSTRUCTIONS (19)
WIM SYSTEM CONTROL INSTRUCTIONS (20)
WIM SYSTEM CONTROL INSTRUCTIONS (21)
WIM SYSTEM CONTROL INSTRUCTIONS (22)
WIM SYSTEM CONTROL INSTRUCTIONS (23)

3.2 Taw qhia rau qhov system interface
WIM SYSTEM CONTROL INSTRUCTIONS (25)

3.3 System parameter teeb tsa
3.3.1 System pib parameter teeb tsa.
(1) Nkag mus rau qhov system teeb tsa dialog box

WIM SYSTEM CONTROL INSTRUCTIONS (26)

(2) Kev teeb tsa parameter

WIM SYSTEM CONTROL INSTRUCTIONS (32)

a. Teem tag nrho qhov hnyav coefficient li 100
WIM SYSTEM CONTROL INSTRUCTIONS (28)
b. Teeb IP thiab tus lej chaw nres nkoj
WIM SYSTEM CONTROL INSTRUCTIONS (29)
c.Tsim tus qauv tus nqi thiab channel
WIM SYSTEM CONTROL INSTRUCTIONS (30)
Nco tseg: thaum hloov kho qhov kev zov me nyuam, thov khaws tus nqi piv txwv thiab channel raws li qhov kev zov me nyuam qub.
d.Parameter teeb tsa ntawm spare sensor
WIM SYSTEM CONTROL INSTRUCTIONS (39)
4. Nkag mus rau qhov chaw calibration
WIM SYSTEM CONTROL INSTRUCTIONS (39)
WIM SYSTEM CONTROL INSTRUCTIONS (38)
5.Thaum lub tsheb hla dhau qhov ntsuas qhov sib npaug (qhov kev pom zoo ceev yog 10 ~ 15km / h), lub kaw lus tsim cov ntsuas qhov hnyav.
6.Reload tshiab qhov hnyav tsis.
(1) Nkag mus rau qhov system nqis.
WIM SYSTEM CONTROL INSTRUCTIONS (40)
(2) Nyem Txuag kom tawm.WIM SYSTEM CONTROL INSTRUCTIONS (41)
5. Kev kho kom zoo ntawm qhov system tsis
Raws li qhov hnyav tsim los ntawm txhua lub sensor thaum lub tsheb txheem dhau los ntawm qhov system, qhov hnyav ntawm txhua lub sensor raug kho manually.
1. Teeb tsa qhov system.
WIM SYSTEM CONTROL INSTRUCTIONS (40)
2.Kho kom raug K-factor raws li kev tsav tsheb ntawm lub tsheb.
Lawv yog pem hauv ntej, hla channel, thim rov qab thiab ultra-low ceev tsis.
WIM SYSTEM CONTROL INSTRUCTIONS (42)
6.System nrhiav kom tau parameter teeb
Teem cov tsis sib xws raws li qhov system nrhiav kom tau.
WIM SYSTEM CONTROL INSTRUCTIONS (46)

System kev sib txuas lus raws tu qauv

TCPIP hom kev sib txuas lus, piv txwv XML hom ntawv rau kev xa cov ntaub ntawv.

  1. Lub tsheb nkag: cov cuab yeej raug xa mus rau lub tshuab sib txuam, thiab lub tshuab sib txuam tsis teb.
Detective taub hau Cov ntaub ntawv lub cev ntev (8-byte ntawv hloov mus rau cov lej) Cov ntaub ntawv lub cev (XML hlua)
DCYW

deviceno=Instrument naj npawb

Roadno = Txoj kev no

recno=Data serial tooj

/>

 

  1. Lub tsheb tawm mus: qhov ntsuas raug xa mus rau lub tshuab sib txuam, thiab lub tshuab sib txuam tsis teb
taub hau (8-byte ntawv hloov dua siab tshiab rau integer) Cov ntaub ntawv lub cev (XML hlua)
DCYW

deviceno=Instrument naj npawb

Roadno = Txoj Kev No

recno =Cov ntaub ntawv serial tooj

/>

 

  1. Upload cov ntaub ntawv hnyav: qhov ntsuas raug xa mus rau lub tshuab sib txuam, thiab lub tshuab sib txuam tsis teb.
taub hau (8-byte ntawv hloov dua siab tshiab rau integer) Cov ntaub ntawv lub cev (XML hlua)
DCYW

ntaus ntawv =Tus lej ntsuas

Roadno = Txoj kev no:

recno=Data serial tooj

kroadno = Hla txoj kev kos npe;tsis txhob hla txoj kev mus sau 0

ceev = ceev;Chav ntsuas kilometer ib teev

luj =Qhov hnyav tag nrho: unit: Kg

axlecount = Tus naj npawb ntawm axes;

kub =kub;

maxdistance = Qhov kev ncua deb ntawm thawj axis thiab lub xeem axis, nyob rau hauv millimeters

axlestruct = qag qauv: piv txwv li, 1-22 txhais tau hais tias ib lub log tsheb ntawm txhua sab ntawm thawj qag, ob lub log ntawm txhua sab ntawm lub qag thib ob, ob lub log ntawm txhua sab ntawm lub qag thib peb, thiab lub qag thib ob thiab lub qag thib peb txuas nrog

weightstruct = Nyhav qauv: piv txwv li, 4000809000 txhais tau tias 4000kg rau thawj qag, 8000kg rau lub thib ob qag thiab 9000kg rau lub thib peb qag

distancestruct = Distance structure: piv txwv li, 40008000 txhais tau hais tias qhov kev ncua deb ntawm thawj axis thiab lub thib ob axis yog 4000 hli, thiab qhov kev ncua deb ntawm lub thib ob axis thiab lub thib peb axis yog 8000 hli.

diff1 = 2000 yog qhov sib txawv millisecond ntawm cov ntaub ntawv hnyav ntawm lub tsheb thiab thawj lub siab sensor

diff2 = 1000 yog qhov sib txawv millisecond ntawm cov ntaub ntawv hnyav ntawm lub tsheb thiab qhov kawg

ntev = 18000;tsheb ntev;mm

dav = 2500;tsheb dav;ib :mm

qhov siab = 3500;tsheb qhov siab;ib mm

/>

 

  1. Cov khoom siv raws li txoj cai: qhov ntsuas raug xa mus rau lub tshuab sib txuam, thiab lub tshuab sib txuam tsis teb.
Lub taub hau (8-byte ntawv hloov dua siab tshiab rau integer) Cov ntaub ntawv lub cev (XML hlua)
DCYW

deviceno=Instrument naj npawb

code = "0" xwm txheej code, 0 qhia qhov qub, lwm qhov tseem ceeb qhia qhov txawv txav

msg=""State description

/>

 


  • Yav dhau los:
  • Tom ntej:

  • Yam khoom